Shop headings: New Spares | Used Spares | Accessories | Brands
99cm length of black pipe with clips for connecting rear master cylinder to brake fluid reservoir
Brake fluid, oil and fuel resistant. This is long enough for the rear brake master cylinder on V50 II and V35 I
More than 5 in stock
£12.00
INC VAT
£10.00 EX VAT
Rubber plug for swing arm pivot locknut
More than 5 in stock
93180105 GU93180105 93 18 01 05
9318 0105 9318.0105 93.18.01.05
£1.20
INC VAT
£1.00 EX VAT
Inlet manifold gasket
Also known as Guzzi ref. 19115500
More than 5 in stock
19115520 GU19115520 19 11 55 20
1911 5520 1911.5520 19.11.55.20
£1.40
INC VAT
£1.17 EX VAT
Input shaft oil seal for gearbox
More than 5 in stock
90403245 GU90403245 90 40 32 45
9040 3245 9040.3245 90.40.32.45
£9.00
INC VAT
£7.50 EX VAT
M16 stainless steel full nut and thick washer for rear wheel spindle
Also referred to as Guzzi ref. 14634400 and 92602316
More than 5 in stock
92602316-z 92602316 GU92602316 92 60 23 16
9260 2316 9260.2316 92.60.23.16
£10.50
INC VAT
£8.75 EX VAT
M16 stainless steel half nut and washers for front wheel spindle. Includes flat and wavy washer
NB this is a half nut. Can also be used as alternator retaining nut 92603516
More than 5 in stock
92602516-z 92602516 GU92602516 92 60 25 16
9260 2516 9260.2516 92.60.25.16
£8.50
INC VAT
£7.08 EX VAT
Taper needle roller bearing used as steering head bearing
2 sets required per bike. Also used as rear drive box pinion bearing on big twins with rear drum brake
More than 5 in stock
92249225 GU92249225 92 24 92 25
9224 9225 9224.9225 92.24.92.25
£20.50
INC VAT
£17.08 EX VAT
Drive box input seal
Pinion oil seal
More than 5 in stock
90403251-z 90403251 GU90403251 90 40 32 51
9040 3251 9040.3251 90.40.32.51
£16.60
INC VAT
£13.83 EX VAT
A2 stainless socket cap screw M5 x 50, used for retaining Saprisa alternator stator
More than 5 in stock
98620250-z 98620250 GU98620250 98 62 02 50
9862 0250 9862.0250 98.62.02.50
£1.20
INC VAT
£1.00 EX VAT
Special tool for tightening and untightening the dipstick on small twins. The dipstick can be awkward to undo on these models but this tool makes it simple and quick. No more struggling to grip it or resorting to pliers, just use our tool.
Oil filler tool manufactured from PETG filament these are fully recyclable but as strong as ABS. Dipstick spanner 3D printed in the UK
More than 5 in stock
14927001 GU14927001 14 92 70 01
1492 7001 1492.7001 14.92.70.01
£12.00
INC VAT
£10.00 EX VAT